M3 4 pot full BBK set up

s.mac · 07-03-2011, 06:20 PM

Hi all, for any E46 M3 drivers you know, if you can pass the word around, they would fit a CSL but you would need to buy the front bracket ( I can point you in the right direction) I will not split though therefore this is really for an M3 owner to take all

For Sale £1,500.00 no offers

I have finally found the time to put my old BBK up for sale.

I used this on my old m3 and took it off prior to selling the car.

It is Rotora branded. They were originally silver with Brembo decals but I had them refinished in yellow with new carbon fibre finish decals.

They have new seals, bleed nipples / piping etc. I am also supplying brand new stainless steel hoses x 4. Plus new pads all round.
I didn't like the original pads and found better pads. I have supplied mintex but you can upgrade to pagid / hawk/ EBC etc and I will let you know the pad shape, the pads I use need 1mm taking off the sides, this is common practice and a 2 min job. The ones supplied are ready to go straight in (Questmead can do this for you if you are not familiar with this). Questmead are my preferred supplier.
I also used performance friction brake discs front and rear, they are OEM size discs, if you don't want to use them you can stick with your OEM disks ( I will not be splitting in the sale)
I had the discs blasted as they had surface rust from being stood in my garage. I had the front bells re anodised and the rears cleaned off.Ive nearly finished putting the hubs on the discs, they will be finished.
I think I have listed everything

These are NOT 100% mint, they have been used before! although I hope enough of you know me to know I have a bit of OCD (not as much as Rob

)
I live in Leeds and am more than happy for a potential buyer to view, in fact I would prefer it.

funtime · 07-03-2011, 06:25 PM

Bargain, looks immaculate mate - i'll pop it on cutters for you

funtime · 07-03-2011, 06:31 PM

M3 Cutters...

s.mac · 07-03-2011, 06:34 PM

cheers

funtime · 07-03-2011, 06:55 PM

Quote:

Originally Posted by s.mac

cheers

No worries, certiantly get some views on there though - I didn't really read your description and advertised them as a "Brembo BBK for £1500"

Ooops!

s.mac · 07-03-2011, 07:13 PM

It makes no odds really, they are Alcon copy, Aston Martin and F40 use them from the research I did

mattCSLnut · 07-03-2011, 07:23 PM

Nice set up Steve, looks like NEW

and well priced

BREMBOs rock

s.mac · 07-03-2011, 07:57 PM

Thanks Matt

Ive spent a good few ££££ sorting it out

I would rather have done it this way, than sell for less and the new owner having the pain getting it sorted. Bar putting the discs on the bells its ready to go.
the callipers can bolt straight on to M3 OEM discs set up if the new owner just wants to put the callipers on

just to note, the discs are OEM size the callipers definitely aren't OEM size !! and they fill the space behind 19s

unlike the CSL cup Alcon kit these were made to work with the OEM master cylinder

Mando188 · 18-03-2011, 01:57 AM

Are they steel for sale??

funtime · 18-03-2011, 09:37 AM

I don't think so mate, they are set as SOLD on Pistonheads...

07-03-2011, 06:20 PM	#1
s.mac CSL Register Uber-poster! Join Date: Jun 2008 Posts: 4,247 Casino cash: $15600	M3 4 pot full BBK set up Hi all, for any E46 M3 drivers you know, if you can pass the word around, they would fit a CSL but you would need to buy the front bracket ( I can point you in the right direction) I will not split though therefore this is really for an M3 owner to take all For Sale £1,500.00 no offers I have finally found the time to put my old BBK up for sale. I used this on my old m3 and took it off prior to selling the car. It is Rotora branded. They were originally silver with Brembo decals but I had them refinished in yellow with new carbon fibre finish decals. They have new seals, bleed nipples / piping etc. I am also supplying brand new stainless steel hoses x 4. Plus new pads all round. I didn't like the original pads and found better pads. I have supplied mintex but you can upgrade to pagid / hawk/ EBC etc and I will let you know the pad shape, the pads I use need 1mm taking off the sides, this is common practice and a 2 min job. The ones supplied are ready to go straight in (Questmead can do this for you if you are not familiar with this). Questmead are my preferred supplier. I also used performance friction brake discs front and rear, they are OEM size discs, if you don't want to use them you can stick with your OEM disks ( I will not be splitting in the sale) I had the discs blasted as they had surface rust from being stood in my garage. I had the front bells re anodised and the rears cleaned off.Ive nearly finished putting the hubs on the discs, they will be finished. I think I have listed everything These are NOT 100% mint, they have been used before! although I hope enough of you know me to know I have a bit of OCD (not as much as Rob ) I live in Leeds and am more than happy for a potential buyer to view, in fact I would prefer it. Last edited by s.mac; 11-03-2011 at 07:33 PM. Reason: put the discs on the bells

07-03-2011, 07:23 PM	#7
mattCSLnut CSL Register Uber-poster! Join Date: Sep 2009 Location: Cambridge Posts: 6,460 Casino cash: $27763	Nice set up Steve, looks like NEW and well priced BREMBOs rock __________________ UK CSL No.020 ... after 7 years of ownership I've now SOLD it !!!

07-03-2011, 07:57 PM	#8
s.mac CSL Register Uber-poster! Join Date: Jun 2008 Posts: 4,247 Casino cash: $15600	Thanks Matt Ive spent a good few ££££ sorting it out I would rather have done it this way, than sell for less and the new owner having the pain getting it sorted. Bar putting the discs on the bells its ready to go. the callipers can bolt straight on to M3 OEM discs set up if the new owner just wants to put the callipers on just to note, the discs are OEM size the callipers definitely aren't OEM size !! and they fill the space behind 19s unlike the CSL cup Alcon kit these were made to work with the OEM master cylinder Last edited by s.mac; 07-03-2011 at 08:24 PM.

18-03-2011, 01:57 AM	#9
Mando188 Wonky 'L' after Washing Join Date: Mar 2011 Location: León Spain Posts: 13 Casino cash: $389	Are they steel for sale?? __________________ *Livin the fast live in fast cars!! 188*

07-03-2011, 06:25 PM	#2
funtime S5, Sport Off, DSC M-track Join Date: Apr 2010 Location: Sussex Posts: 613 Casino cash: $5830	Bargain, looks immaculate mate - i'll pop it on cutters for you

07-03-2011, 06:31 PM	#3
funtime S5, Sport Off, DSC M-track Join Date: Apr 2010 Location: Sussex Posts: 613 Casino cash: $5830	M3 Cutters...

07-03-2011, 06:34 PM	#4
s.mac CSL Register Uber-poster! Join Date: Jun 2008 Posts: 4,247 Casino cash: $15600	cheers

07-03-2011, 07:13 PM	#6
s.mac CSL Register Uber-poster! Join Date: Jun 2008 Posts: 4,247 Casino cash: $15600	It makes no odds really, they are Alcon copy, Aston Martin and F40 use them from the research I did

18-03-2011, 09:37 AM	#10
funtime S5, Sport Off, DSC M-track Join Date: Apr 2010 Location: Sussex Posts: 613 Casino cash: $5830	I don't think so mate, they are set as SOLD on Pistonheads...