CSL Register

Go Back   CSL Register > General > Technical Area

Reply
 
Thread Tools Display Modes
Old 25-10-2017, 06:16 PM   #51
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Quote:
Originally Posted by Chad View Post
When I’ve measured crank bearing face they come out as in photo, so std crank. Very minimal wear on this 100k crank , would have been ideal if bmw give you the option of shells as they do on main shells, especially for no 3 .
I’ve taken picture from internet,,, What’s the recommend ideal measurement outcome for csl shells ??? I’ estimate I will see .05 plastagauge on rod no 3 shell from what I’ve measured with micrometer, tighter on others. Possibly down to .02 mm
Attached Images
File Type: jpg 18A9040C-AC75-4495-92C3-3D52631ADD2B.jpg (16.8 KB, 107 views)

Last edited by Chad; 25-10-2017 at 10:49 PM.
Chad is offline   Reply With Quote
Old 28-10-2017, 01:02 PM   #52
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Quote:
Originally Posted by Monkey View Post
Hi Chad,

You are correct there are only 2 sizes of bearing available for the big ends, and yes there is a standard size and an option for ground cranks.

As for the mains there is a wider selection of bearing sizes avaiable.

As I mentioned previously, I would only recommend using plastiguage to see which bearing shells you need.
Hi James , top marks to you mate going to the trouble of checking with plastiguage, I’m sure 99percent wouldn’t.. I’ve today been round all local autos spares, not one of them even heard of it , never mind what it’s used for.... Having established I’ve got stock crank and only the one shell available, still what is the ideal measurements outcome we are looking for , regarding plastiguage on these bmw crank to bearing face measurements, Eg 0.03 0.02 mm, Do bmw have a recommendation. ???.... sort of irrelevant I know as only one shell available , Any input also welcomed anybody

Last edited by Chad; 28-10-2017 at 01:05 PM.
Chad is offline   Reply With Quote
Old 31-10-2017, 12:02 AM   #53
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Found this on internet, bit more information , but no dimensions. Definitely plastiguage will be used to work out best one to use on mains , but could do with actual tolerance required.? Eg if the white shell has more meat on its bones,(so to speak) I’d possibly use this on Number 1 main. As this has the most wear, as this crank used green shells from new . All depending on what bmw recommed shell to crank tolerance....If anybody knows ?
Attached Images
File Type: jpg 1C553247-45CD-48EE-9470-6B37C48D4B03.jpg (19.7 KB, 83 views)
File Type: jpg 2D759D5E-CBE1-4D94-9BFC-E42F8E67F623.jpg (19.9 KB, 85 views)

Last edited by Chad; 31-10-2017 at 12:47 AM.
Chad is offline   Reply With Quote
Old 31-10-2017, 01:18 AM   #54
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Think this is what I need.
Attached Images
File Type: jpg 17BF214E-EE53-4799-A832-9E7A0A51DD0E.jpg (19.9 KB, 85 views)

Last edited by Chad; 31-10-2017 at 01:23 AM.
Chad is offline   Reply With Quote
Old 09-11-2017, 10:46 PM   #55
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default Plastiguage

Eventually got some plastiguage from manufacturers, pictures couple of main crank journals , and the two most abused rod journals, shows a basic ball park measurements of bearings wear /conditions .. to compare against bmw bearings chart in previous post. . My measurements with basic micrometer shows a slight difference to bmw spec , Will recheck with a better mic Just to check crank spec again. These are the worn bearings. So new should but them back to spec. Number one main crank shell seems to pull the most wear , about 0.055 mm possibly as it pulls timingchain / oil pump, .... Conrod bearing clearance. Should be between 0.030. And 0.070 mm on spec sheet,Below 0.030 is to tight bmw recommendation would be to fit another set of new shells .(... Update... ) bmw now, say min 0.040 shell bearing clearance, After that new Conrods

Last edited by Chad; 11-11-2017 at 05:45 PM.
Chad is offline   Reply With Quote
Old 10-11-2017, 10:15 PM   #56
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default Rod bearings spec

If off interest to anybody rod Journal bearing spec and shell clearance. ........NOW from what I’ve read bmw have changed from min 0.03. To min 0.04. Retrospectively. (I’d work to 0.04 ).
Attached Images
File Type: jpg 1A7797B2-AEB1-46C2-930A-C840EB13EE66.jpg (8.2 KB, 61 views)

Last edited by Chad; 11-11-2017 at 09:52 AM.
Chad is offline   Reply With Quote
Old 12-11-2017, 06:53 PM   #57
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Quote:
Originally Posted by Chad View Post
Thanks James for confirming that regarding rod shells, as for main shells, is there any technical information as regards thickness difference of the yellow, green,and white shells on std shells, I’m assuming they are only different in 0.01. Or 0.03 difference so to speak just to take up a bit of wear on crank bearing faces. ........ Sorry to blast you with this. Also regarding ring sizes shows two different ring options for std rings, 0 and 00. I’m presuming 00 are to be used on a higher mile engine , any tech info on this appreciated ? £40 price difference also between the two different part numbers I understand measuring end gap etc. ..... Any specific end gap for csl.. thanks for your input James. ,,, speaking to my local engineer suppliers today, they say they would use the 00 term / measurements, to indicate a higher degree of machined /measured accuracy. Phil
..found ring clearance, if anybody needs to know, also main bearings shell Difference....as for ring sizes bmw shows three sizes, 0 and 00 And +0.20 From what I’ve found I think it is the bore size, as on engine block spec picture bellow, So I’m guessing not all blocks are the same, and need to be checked when ordering pistons and rings , unless anybody knows differently, ??? Possibly+0.20 is first oversized,
Attached Images
File Type: jpg 4B73EFCC-B349-4CF4-84EF-81E17FF6EB6F.jpg (17.5 KB, 52 views)
File Type: jpg B85C2C0E-4E71-4F65-89F2-CA8A10CC0795.jpg (19.9 KB, 49 views)
File Type: jpg ED8060F6-4382-435F-9941-3AF05E3B54E1.jpg (21.1 KB, 48 views)

Last edited by Chad; 12-11-2017 at 10:35 PM. Reason: A
Chad is offline   Reply With Quote
Old 21-11-2017, 10:38 AM   #58
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Quote:
Originally Posted by Monkey View Post
Hi Chad,

You are correct there are only 2 sizes of bearing available for the big ends, and yes there is a standard size and an option for ground cranks.

As for the mains there is a wider selection of bearing sizes avaiable.

As I mentioned previously, I would only recommend using plastiguage to see which bearing shells you need.
. Just to add to the post regarding mains shells , and colour coded shells.
Attached Images
File Type: jpg 0C185BDB-0074-4EB8-BBC7-AD020FD4E821.jpg (6.2 KB, 48 views)
File Type: jpg 50343705-ADC5-4791-86CD-0F2A7572C2FC.jpg (19.7 KB, 38 views)

Last edited by Chad; 22-11-2017 at 08:33 AM.
Chad is offline   Reply With Quote
Old 21-11-2017, 01:26 PM   #59
Mike R
S6, Sport On, Traction Off
 
Mike R's Avatar
 

Join Date: Dec 2010
Location: Norwich
Posts: 1,582
Casino cash: $17548
Mike R is on a distinguished road
Default

Superb reference information
__________________
Mike R
Sarcasm is just a free service I provide.

Nordschleife, there's only two barriers to worry about - the ones on the left and the ones on the right .

CSL number 044
Mike R is offline   Reply With Quote
Old 01-01-2018, 05:53 PM   #60
Chad
S5, Sport Off, DSC M-track
 
Chad's Avatar
 

Join Date: May 2015
Location: Cheshire
Posts: 631
Casino cash: $7782
Chad is on a distinguished road
Default

Sorry chaps but nothing better to do . So thought I’d put a comparison of new shells i have , , “”mains”” Black shell king race, silver oem yellow code shells mains inc thrust bearings, note different elongated hole in king shells. Also picture of rod shells black kings. Silver bmw, with weight of rod bearings. Will do weights of mains later. These king bearings do look to have good surface finish and look like a good quality finish.... “” Anybody have experience of the king race””.

Last edited by Chad; 01-01-2018 at 07:53 PM.
Chad is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 12:46 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c)www.wickedwifi.co.uk