CSL Register

CSL Register (http://www.cslregister.com/forum/index.php)
-   Technical Area (http://www.cslregister.com/forum/forumdisplay.php?f=16)
-   -   How to replace your speakers with something better ! (http://www.cslregister.com/forum/showthread.php?t=681)

rs32 03-10-2008 06:54 PM

How to replace your speakers with something better !
 
I've posted this as it hopefully serves a purpose for any people wanting to get improved sound in their cars without cutting/drilling/fabricating anything. This isn't the most complex job in the world - but there's very little material out there for those who want to dabble in a bit of OEM+

Have been keen to improve the audio in the CSL as although it has an amazing soundtrack of its own, the speakers are woeful and do not do a 60k car justice - not even close.

The problem with the CSL is that BMW used a mish-mash of E46 audio components - so even clever companies like Rainbow did not make a kit as an OEM replacement.

So I decided to dig further, and came up with a plan. The rear shelf speakers (mid-bass) looked as if they were the same as the E46 Coupe front speakers, based on info from RealOEM.com. I had this checked via my trusted audio installers and Rainbow - and I was right.

However Rainbow only sell the front kit as a component set (mid-bass plus tweeter, all interconnected from factory), meaning I would need 2 front sets and some tweaking to complete the job.

http://i179.photobucket.com/albums/w...2/IMG_0002.jpg

So today I attacked the task of the rear shelf jobbies. Thanks to Rainbow for the clear instructions :119:

http://i179.photobucket.com/albums/w...2/IMG_0014.jpg

A few tools needed, but nothing too exciting - main things were trim removal spatula and 8mm socket.

http://i179.photobucket.com/albums/w...2/IMG_0004.jpg

Here's the working area, not much space so it's all a bit fiddly.

http://i179.photobucket.com/albums/w...2/IMG_0005.jpg

OEM speaker in situ, having removed the grille and foam insert.

http://i179.photobucket.com/albums/w...2/IMG_0007.jpg

http://i179.photobucket.com/albums/w...2/IMG_0006.jpg

Undo the three bolts (this is the killer design issue with all the OEM replacement sets on the market - none of them are designed as single items with the 3 bolt pattern) - and remove the OEM speaker.

http://i179.photobucket.com/albums/w...2/IMG_0008.jpg

http://i179.photobucket.com/albums/w...2/IMG_0009.jpg

Compare OEM with Rainbow IQ-Line replacement. Notice the difference in magnet size, speaker cone materials and separate crossover for the Rainbow item. You can see why the OEM ones only cost about $30.

http://i179.photobucket.com/albums/w...2/IMG_0010.jpg

http://i179.photobucket.com/albums/w...2/IMG_0011.jpg

Now the tricky bit - need to remove the crossover for the tweeter connection, so carefully strip back the wire join shrink-wrap, chop the tweeter connection wires and tape up.

http://i179.photobucket.com/albums/w...2/IMG_0016.jpg

Leaving 2 "prepared" new speakers ready to be fitted.

http://i179.photobucket.com/albums/w...2/IMG_0018.jpg

Next problem - the new speakers have the crossovers cable-tied around the magnets and BMW did not allow for that extra width when they designed the mounting assembly for the OEM versions - so they needed sliding round on the cable tie and I also tidied the wire extension around the magnets so that excess cable would not get in the way when refitting.

Now link up the new speakers ot the OEM connectors - remembering that the speaker "phase" (positive/negative connections) needs to be right. I do this by listening and checking the movement of the speaker at a low test volume - pretty easy to tell when it's wrong. Then need to secure the connection with a bit more tape.

http://i179.photobucket.com/albums/w...2/IMG_0021.jpg

Carefully drop the new speaker into the OEM fitting, ensuring no wiring is trapped and allowing the large speaker assembly to fit into the OEM hole.

Replace OEM screws and job done. Foam insert and grille fits right back over the top no problem.

http://i179.photobucket.com/albums/w...2/IMG_0023.jpg

What about the sound ? With just the two rears done it's a SIGNIFICANT improvement - there is actually bass and mid punch now rather than some muddled farting noises. Clear, precise (OK not exactly competition standard) - but a great upgrade for the money (about £125 per pair) and when the fronts are done it will be an excellent sound.

Planning on doing the fronts tomorrow so will add more here when done :thumbs:

dave1 03-10-2008 07:04 PM

looks good so have you joined the bm wires to the crossover or the speaker?

rs32 03-10-2008 07:14 PM

to the crossover - it limits the mid/bass drivers to 6kHz instead of 10kHz - am assuming the Rainbow design has a different "shift" point between the bass/mid/tweeter frequencies compared to the OEM setup.

Would also explain why the OEM setup sounds so crap if the bass drivers are trying to play 10kHz through cheap Hungarian paper cones :banghead:

dave1 03-10-2008 07:29 PM

sounds good might go this way also the standard stuff is horrendous

rs32 03-10-2008 07:35 PM

check back here Dave after end of tomorrow to take a look at the fronts (no idea what to expect yet on this).

also let me know if you want to order the same as I did - because my supplier might be able to get you a good deal. The kit came straight from Germany and took about 5 days.

shimmy 03-10-2008 08:55 PM

speakers???

what do you need them for. Have you got one of thise modern fangled stereos!!??????

rs32 03-10-2008 09:12 PM

I get asked why on earth you would want to worry about speakers in a CSL quite a lot.

but I don't care :thumbs:

glendog74 03-10-2008 10:33 PM

Nice info - cheers :beer:

rs32 04-10-2008 01:42 PM

Have now completed the fronts and the results are impressive for 3.5 hours effort.

Full instructions and pics to follow....

rs32 04-10-2008 03:10 PM

So onto the front speakers – replacement of OEM 6.5” mid/bass drivers and tweeters with Rainbow IQ-line components. This install differs from the rear install as it makes use of the full crossover capability of the Rainbow kit.
Same starting point – new components.

http://i179.photobucket.com/albums/w...2/IMG_0002.jpg

I was a bit apprehensive about messing around with the door cards – but here goes.
Firstly remove the screw cover inside the door pull – use a very thin-tip flat screwdriver and take care not to ruin the fairly soft plastic. Mine already had some scratches. Undo this screw fully with a Torx T20 bit and put in a safe place.

http://i179.photobucket.com/albums/w...2/IMG_0025.jpg

Then remove the 2 door handle bolts with a Torx T40 bit – they are very tight at the start then nice and easy – again put them in a safe place.

http://i179.photobucket.com/albums/w...2/IMG_0029.jpg

Now the dreaded door card clips – using a wide, flat trim removal tool, start at the bottom left and work your way around the bottom of the door from left to right. A fair bit of (measured) force is required, don’t be afraid to give it a decent prising force but no sudden force as you could damage the plastic clips. Same for the upper left and right clips.

http://i179.photobucket.com/albums/w...2/IMG_0031.jpg

http://i179.photobucket.com/albums/w...2/IMG_0030.jpg

Now the top edge by the window line needs unclipping. Again – a fair bit of force is required but be patient as they are quite tight. Start form the top left and move towards the right (door pin end) – obviously the direction changes dependant on which door you are doing.

http://i179.photobucket.com/albums/w...2/IMG_0032.jpg

You should end up being able to pull the door card upwards and then completely away from the door metal – but it will still be held on by the door release cable. This needs unclipping by pulling away from you – quite easy but take care so as not to smack the door card back into the door metal.

http://i179.photobucket.com/albums/w...2/IMG_0033.jpg

Now the speaker connections can be unclipped and the card is completely free of the door. So far so good.

http://i179.photobucket.com/albums/w...2/IMG_0034.jpg

Find a good flat surface and lay out a towel or something else that will protect the carbon/plastic face of the door card.
Remove the sound-deadening around the speaker – I made the mistake of thinking this should be reused but we’ll come to that bit later. Unclip the tweeter connection from the 6.5” speaker unit. There are three cross-head screws that need removing for the 6.5” speaker and 3 Torx T20 screws for the tweeter assembly – undo all of these and remove the OEM speakers from the door card.

http://i179.photobucket.com/albums/w...2/IMG_0036.jpg

http://i179.photobucket.com/albums/w...2/IMG_0041.jpg

http://i179.photobucket.com/albums/w...2/IMG_0042.jpg

The next bit needed a bit of thought – I didn’t want anything to rattle but using tape isn’t the best idea – so decided to combine the sticky properties of Dynamat Extreme sound-deadening with the routing of the component set wiring. I started with the 6.5” replacement, found a good location for the mini-crossover unit and secured it into place with thin acoustic carpet (as packing material) and the Dynamat then routed all the wiring – again using the Dynamat. More carefully-placed strips of Dynamat round the plastic bits immediately surrounding the speaker – this stop sound transferring from speaker to plastic and means the sound will project from the speaker rather than get all muddied and crap.

http://i179.photobucket.com/albums/w...2/IMG_0044.jpg

For the tweeter I realised that the Rainbow pre-fab assembly could rattle – so again by using acoustic carpet I made a “sandwich” layer and cut out a rough hole for the tweeter to fire through. This plus the Dynamat means it fits nice and snugly when screwed back into place.

http://i179.photobucket.com/albums/w...2/IMG_0046.jpg

http://i179.photobucket.com/albums/w...2/IMG_0047.jpg

http://i179.photobucket.com/albums/w...2/IMG_0049.jpg

For the 6.5” and tweeter units I just reused the OEM screws and everything went nicely back in. Some more tactical Dynamat on plastic surfaces that could resonate and the door card is ready.

Started with this

http://i179.photobucket.com/albums/w...ard_before.jpg

Ended up with this (ignore the sound-deadening around the 6.5” speaker in this pic)

http://i179.photobucket.com/albums/w...card_after.jpg

Then back to the car – the metal door skin also needs Dynamat – particularly on the area directly where the speaker is going to fire. I cannot stress enough how much of a difference this makes – would recommend spending the time on the door metal to get the best value out of your speaker investment. I also chose to do a few other areas where resonance could occur. Note I haven't gone too mental with the Dynamat - just enough to stop the door metal trying to behave like a speaker.

http://i179.photobucket.com/albums/w...2/IMG_0053.jpg

Then the door card needs re-hanging on the door. Reverse the approach to taking it off remembering to fix the door pull cable on first – but only clip in the top piece so the speakers need connecting to the OEM door wiring.

Then from underneath the door you can plug in the speaker wires to the OEM connector block – I then wrapped this in a small piece of acoustic carpet and taped round to ensure no rattling and some protection for the home-made connector.

This is the point where you MUST check the speaker phase (positive/negative connections. As with the rears – low volume and listening to the sound it’s pretty easy to tell which is the right way. Don’t leave this bit until after you’ve refitted as it will be a bugger to fix !

Then push in all the remaining door card clips – firm force required without being brutal. Make sure the speaker connection wires are safely out of the way so they don’t get damaged.

So why not reuse the OEM sound deadening round the 6.5” speaker ? Well I tried the door card half-on with the volume up a bit – then 2/3 on to double-check – and it sounded pretty rubbish. The Rainbow kit seems to prefer having more room to breathe – so I ditched the material.

Double-check all the clips are tightly fixed, then refit the large Torx T40 bolts – might need some nifty handiwork to get them lining up correctly inside the door card – then refit the Torx T20 screw into the door handle assembly, replace the plastic cover and all done !

http://i179.photobucket.com/albums/w...2/IMG_0054.jpg

The difference is pretty astonishing – I’ve gone for fading the system back 1 or 2 notches, Bass up 2 and Treble at the middle setting. For a speaker-only upgrade, this is well worth the ££ and time.

The rears took me 2.5 hours and the fronts 3.5 – but I did the second front door in about an hour including removal and refitting. Very glad I spent the time routing all the wires and checking everything carefully as it all worked first time and has now given me the audio quality that the car should have been given from factory. More than happy with the with the results !


All times are GMT +1. The time now is 07:43 AM.

Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c)www.wickedwifi.co.uk